• 

  点击输入文字描述

• 

  点击输入文字描述

一、多线报警控制器Conventional Fire Alarm Control panel）——简称多线主机或者多线控制器；多线控制面板等。多线主机以回路多少论英雄。市场主打的有4、8、16回路（Zone/区）,以CK1004（4区）,CK1008（8区）,CK1016（16区）为例。主要特点：供电电压AC90-270V, 输出电压 DC24V 每回路烟探：25个；烟感类型：多线烟感/温感/烟温复合（Conventional Smoke / Heat /Smoke & Heat Detector），或者常开输出的开关量信号烟感（4-Wire Smoke Detector with Relay Output）报警反馈输出（SOUND）：每4区共用一个。备电：需配2节12V/7A的铅酸蓄电池—否则会报备电故障(备电电池用户自行配置)界面显示：每个烟感回路有对应的故障和火警显示灯，以及主电，备电，静音（声光），消 音（主机），总故障，火警，报警输出回路的显示灯。操作按钮：5个操作按钮：Silence（火警输出—声光静音），Mute（消音按键），Test(自检按钮)，Reset（复位按钮），Mode（系统设置按钮）。

   二、多线烟感/温感/烟温复合：多线探头是通用的，可接于任何多线主机中。也可配套卷帘门控制箱使用。探头报警之后，会以拉低电压的方式将信号反馈给控制器。门灯（Remote LED）直接接于烟探底座上。烟探报警后会启动对应的门灯。以烟感YT102为例。供电电源： DC9V～DC28V ，静态电流 ≤60uA ，报警电流 ≤30mA，工作温度： -10℃～+50℃ 。

   三、手动报警按钮（Conventional Manual Call Point），工作电压为DC24V，接线方式有常开接法和常闭接法（插钥匙或拔钥匙启动报警），以及串联（参与串联的手报全部同时动作才可启动报警）和并联接法。手报和烟感接于同一回路中。

    四、声光报警器（Sound and light alarm/ Sound Strobe），工作电压：DC24V，现场声光报警，接于报警输出回路，起到火警警告和疏散的作用。频闪（Strobe），警铃（Bell），与声光
类似。

型号：CK1004

全英文产品 外贸主机 出口主机 国内用配有中文接线图

备注:主机内备电电池需客户自行配置(7AH/12V,2节) 主机本身不带电池.

The CK1000 is a 4-zone to 16-zone FACP (Fire Alarm Control Panel), which uses conventional input devices.  The panel accepts water flow devices, two-wire smoke detectors, four-wire smoke detectors, pull stations and other normally-open contact devices. Outputs include four Notification Appliance Circuits (NAC, SOUND1-4), three standard Form-A relays (alarm, trouble and supervisory) and an EIA-485 port to interface with remote annunciators and optional remote relay modules. The FACP is field programmable via the panel keypad.  It also supervises all wiring, AC voltage and battery level.

This series of panels are basically the same in application and operation, their differences are shown in Table 1-1. CK1000 will be described as the example in the following sections.

Table 1-1

1.1 ProductFeatures

l      4,8,16 Class B Initiating Device Circuits (IDCs)

??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??77771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??777771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??77771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??7777777??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??77771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??777771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??77771??1??71??1??771??1??71??1??7771??1??71??1??771??1??71??1??7777777   All zones accept conventional detectors and any normally open contact device

l      Four Class B Notification Appliance Circuits (NACs)

l      One Form-A Alarm Relay

l      One Form-A Trouble Relay

l      One Form-A Supervisory Relay

l      3.0 amps of system power

l      Max 20 conventional detectors in one zone.

l      Auto/Manual mode setting enable walk test.

l      Each Zone can be disabled,

l      Sound output can be disabled.

l      Manual active sound output enabled.

l      Able to report short and broken circuit of detection zones.

l      Designed with standby batteries and space provision for two sealed lead-acid batteries.

l      Testing and disable functions.

AC Power

AC90-270 VAC, 50 Hz, 2.3 amps

Wire size: minimum #14 AWG (2.0 mm²) with 600V insulation

Battery(lead acid only)

Maximum Charging Circuit: Normal Flat Charge—27.6V @ 0.8 amp

Maximum Charger Capacity: 18 Amp Hour batter

Sound Output Device Circuits

General Alarm Zones 1 through 16

Operation: All zones Class B

Normal Operating Voltage: Nominal 24 VDC (ripple = 100 mV maximum)

Alarm Current: 15 mA threshold

Short Circuit Current: 42 mA maximum

Maximum Loop Resistance: 100 ohms

End-of-Line Resistor: 4.7K, ½ watt

Detector Loop Current is sufficient to ensure operation of two alarmed detectors per zone

Standby Current: 7.26 mA

Three Relays Output

Relay contact rating: 2.0 amps @ 30 VDC (resistive), 2.0 amps @ 30 VAC (resistive)

Nonresettable 24 VDC Power

Maximum ripple voltage: 10 mVRMS          Operating Voltage nominal 24 volts

Total DC current available from this output is up to 500 mA

Recommended maximum Standby current is 150 mA